Archives

CB8

Fully assembled housing is formed and welded, 20 ga. steel, chemically treated to resist corrosion and enhance paint adhesion

Standard finish is high reflectance white powder coat, applied post production

Rotational locking lamp holders

Available for one or two T8 17W, 25W, 32W or 40W linear fluorescent lamps

Standard Universal voltage electronic high power factor ballast is pre-wired to the lamp holders

Dimming and emergency battery back up options available (consult factory for availability and system

compatibility)

UL and ULC listed for dry and damp locations

IBEW manufactured and assembled

Made in U.S.A.

BSS205

Fixture constructed of an extruded aluminum housing, extruded, frosted acrylic lens and machined aluminum end caps.

Model variations offered in rectangular or rounded profiles for surface, wall mount and cable suspended mounting with solid or luminous end options.

Standard finishes include architectural white (semi-matte), white (semi-gloss), black (semi-matte), matte black, environmental  satin silver (alternative to anodize), bronze and primer powder coat, applied post production (consult factory for custom finishes).

Satin anodize finish also available (may require additional lead time).

Available in nominal 2’–8’ single fixtures and continuous runs.

Basic continuous run fixtures provided with 18 ga. wiring harness for 6 Amp maximum load (consult factory for runs requiring multiple circuits, sensor integration, etc.).

Standard integral 120-277V driver offered with 0-10V dimming or non-dim (other dimming driver options available).

Integral 120-277V emergency battery backup available for 4’ nominal non-dim or 0-10V (consult factory for all other lengths/drivers).

Standard light outputs are 600 or 800 lumens per foot.

LEDs available in 2700K, 3000K, 3500K, and 4000K, within a 3 step MacAdam ellipse, all with 90+ CRI typical.

Life: 50,000 hours L70.

Bartco Lighting Controls Capable fixture available with integrated controls from a variety of suppliers (FOR RECTANGULAR PROFILE ONLY).

Limited five year warranty.

UL and C-UL listed for dry and damp locations.

IBEW manufactured and assembled.

Made in U.S.A.

BSS210

Fixture constructed of an extruded aluminum housing, extruded, frosted acrylic lens and machined aluminum end caps.

Model variations offered in rectangular or rounded profiles for surface and wall mount or cable suspended applications with solid or luminous end options.

Standard finishes include architectural white (semi-matte), white (semi-gloss), black (semi-matte), matte black, environmental satin silver (alternative to anodize), bronze and primer powder coat, applied post production (consult factory for custom finishes).

Satin anodize finish also available (may require additional lead time).

Available in nominal lengths of 2’–8’ single fixtures and continuous runs.

Basic continuous run fixtures provided with 18 ga. wiring harness for 6 Amp maximum load (consult factory for runs requiring multiple circuits, sensor integration, etc.).

Standard integral 120-277V driver offered with 0-10V dimming or non-dim (other dimming driver options available).

Integral 120-277V emergency battery backup available for 4’ nominal non-dim or 0-10V (consult factory for all other lengths/drivers).

Standard light outputs are 600 or 1000 lumens per foot.

LEDs available in 3000K, 3500K, 4000K and 5000K, within a 3 step MacAdam ellipse, all with 80+ CRI typical.

Life: 50,000 hours L70.

Bartco Lighting Controls Capable fixture available with integrated controls from a variety of suppliers (FOR RECTANGULAR PROFILE ONLY).

Limited five year warranty.

UL and C-UL listed for dry and damp locations.

IBEW manufactured and assembled.

Made in U.S.A.

BSS215

Fixture constructed of an extruded aluminum housing, extruded, frosted acrylic lens and machined aluminum end caps.

Model variations offered for surface, wall mount and cable suspended mounting with solid or luminous end options.

Standard finishes include architectural white (semi-matte), white (semi-gloss), black (semi-matte), matte black, environmental satin silver (alternative to anodize), bronze and primer powder coat, applied post production (consult factory for custom finishes).

Satin anodize finish also available (may require additional lead time).

Available in nominal lengths of 2’–8’ single fixtures and continuous runs.

Basic continuous run fixtures provided with 18 ga. wiring harness for 6 Amp maximum load (consult factory for runs requiring multiple circuits, sensor integration, etc.).

Standard integral 120-277V driver offered with 0-10V dimming or non-dim (other dimming driver options available).

Integral 120-277V emergency battery backup available for 4’ nominal non-dim or 0-10V (consult factory for all other lengths/drivers).

Standard light outputs are 600, 840 or 1135 lumens per foot.

LEDs available in 3000K, 3500K, 4000K, 5000K, within a 3 step MacAdam ellipse, all with 80+ CRI typical.

Life: 50,000 hours L70.

Bartco Lighting Controls Capable fixture available with integrated controls from a variety of suppliers.

Limited five year warranty.

UL and C-UL listed for dry and damp locations.

IBEW manufactured and assembled.

Made in U.S.A.

BSS500

Fixture constructed of an extruded aluminum housing, frosted acrylic extruded lens and machined aluminum end caps

Standard finishes include architectural white (semi-matte), white (semi-gloss), black (semi-matte), matte black, environmental satin silver (alternative to anodize), bronze and primer powder coat, applied post production (consult factory for custom finishes)

Satin anodize finish also available (may require additional lead time)

Available in nominal lengths of 2’–8’ single fixtures and continuous runs

Included standard remote 120-277V driver offered with 0-10V dimming or non-dim (other dimming driver options available)

Remote mounted emergency battery backup available (ordered separately, consult factory for details)

Standard outputs are 400 and 525 lumens per foot

LEDs available in 2700K, 3000K, 3500K, and 4000K, within a 3 step MacAdam ellipse, all with 90+ CRI typical

Life: 50,000 hours L70

Limited five year warranty

UL and C-UL listed for dry and damp locations

IBEW manufactured and assembled

Made in U.S.A.

BSS510

Fixture constructed of an extruded aluminum housing, frosted acrylic extruded lens and sheet aluminum end caps

Standard finishes include architectural white (semi-matte), white (semi-gloss), black (semi-matte), matte black, environmental  satin silver (alternative to anodize), bronze and primer powder coat, applied post production (consult factory for custom finishes)

Satin anodize finish also available (may require additional lead time)

Available in nominal lengths of 2’–8′ single fixtures and continuous runs

Included standard remote 120-277V driver offered with 0-10V dimming or non-dim (other dimming driver options available)

Remote mounted emergency battery backup available (ordered separately, consult factory for details)

Standard outputs are 640, 830 and 1090 lumens per foot

LEDs available in 2700K, 3000K, 3500K, and 4000K, within a 3 step MacAdam ellipse, all with 90+ CRI typical

Life: 50,000 hours L70

Limited five year warranty

UL and C-UL listed for dry and damp locations

IBEW manufactured and assembled

Made in U.S.A.

BSS520

Fixture constructed of an extruded aluminum housing, frosted extruded acrylic lens and sheet aluminum end caps

Standard finishes include architectural white (semi-matte), white (semi-gloss), black (semi-matte), matte black, environmental  satin silver (alternative to anodize), bronze and primer powder coat, applied post production (consult factory for custom finishes)

Satin anodize finish also available (may require additional lead time)

Available in nominal lengths of 23”–89” single fixtures and continuous runs

Continuous run fixtures provided with quick connects for simple, efficient wiring

Single and Starter fixtures include coordinating (white, metal braided) 18 ga. power cable

Standard integral 120-277V driver offered with 0-10V dimming or non-dim (other dimming driver options available)

Integral 120-277V emergency battery backup available for 45”–89” fixtures (remote battery backup available for shorter fixture lengths – ordered separately, consult factory for details)

Standard outputs are 5W or 8W nominal per foot

LEDs available in 3000K, 3500K, 4000K, 5000K, all with a typical 84-85 CRI and color consistency within a 3 step MacAdam ellipse

Life: 50,000 hours L70

Limited five year warranty

UL and C-UL listed for dry and damp locations

IBEW manufactured and assembled

Made in U.S.A.

BSS501

Fixture housing constructed of an extruded aluminum tube, frosted acrylic extruded lens and sheet aluminum end caps

Fixture arms are constructed of steel pipe, Ø5/8” extruded aluminum sleeves and machined aluminum end cap couplers.

Mounting plate options include a Ø4-3/4” aluminum plate for mounting to 4” octagonal wall boxes or Ø1-3/8” aluminum plate for mounting to accessible panels.

Standard finishes include architectural white (semi-matte), white (semi-gloss), black (semi-matte), matte black, environmental satin silver (alternative to anodize), bronze and primer powder coat, applied post production (consult factory for custom finishes)

Satin anodize finish also available (may require additional lead time)

Single and continuous run fixtures available with arm center distances of 24”-90”

Arms allow fixture to project from a wall or ceiling nominally 3”, 6”, 12” or 18”

Fixture housing rotates 332° and is locked in place with hex fastener

Included standard remote 120-277V driver offered with 0-10V dimming or non-dim (other dimming driver options available)

Fixture wired with 10’, low voltage leads (measured from the end cap)

Standard outputs are 400 and 535 lumens per foot, dependent on optic

LEDs available in 2700K, 3000K, 3500K, and 4000K, within a 3 step MacAdam ellipse, all with 90+ CRI typical

Life: 50,000 hours L70

Limited five year warranty

UL and C-UL listed for dry and damp locations

IBEW manufactured and assembled

Made in U.S.A.

BSS305

Fully assembled housing is formed and welded, 20 ga. steel, chemically treated to resist corrosion and enhance paint adhesion

Standard finishes include architectural white (semi-matte), white (semi-gloss), black (semi-matte), matte black, environmental satin silver, bronze and primer powder coat, applied post production (consult factory for custom finishes)

Knock-outs accept standard electrical fittings (by others)

Available in nominal lengths of 2’–5’

Includes frosted acrylic lay in lens

Standard integral 120-277V driver offered with 0-10V dimming or non-dim (other dimming driver options available)

Options include 120V or 277V on/off rocker switch and passive infrared occupancy sensor

Standard outputs are 545 and 740 lumens per foot

LEDs available in 2700K, 3000K, 3500K, and 4000K, within a 3 step MacAdam ellipse, all with 90+ CRI typical

Life: 50,000 hours L70

Limited five year warranty

IBEW manufactured and assembled

Made in U.S.A.

BSS511

Fixture housing constructed of an extruded aluminum tube, frosted acrylic extruded lens and sheet aluminum end caps

Fixture arms are constructed of steel pipe, Ø5/8” extruded aluminum sleeves and machined aluminum end cap couplers

Mounting plate options include a Ø4-3/4” aluminum plate for mounting to 4” octagonal wall boxes or Ø1-3/8” aluminum plate for mounting to accessible panels

Standard finishes include architectural white (semi-matte), white (semi-gloss), black (semi-matte), matte black, environmental  satin silver (alternative to anodize), bronze and primer powder coat, applied post production (consult factory for custom finishes)

Satin anodize finish also available (may require additional lead time)

Single and continuous run fixtures available with arm center distances of 24”–68” nominal

Arms allow fixture to project from a wall or ceiling nominally 4”, 6”, 12” or 18”

Fixture housing rotates 332° and is locked in place with hex fastener

Included standard remote 120-277V driver offered with 0-10V dimming or non-dim (other dimming driver options available)

Remote mounted emergency battery backup available (ordered separately, consult factory for details)

Fixture wired with 10’, low voltage leads (measured from the end cap)

Standard outputs are 640, 830 and 1090 lumens per foot

LEDs available in in 2700K, 3000K, 3500K, and 4000K, within a 3 step MacAdam ellipse, all with 90+ CRI typical

Life: 50,000 hours L70

Limited five year warranty

UL and C-UL listed for dry and damp locations

IBEW manufactured and assembled

Made in U.S.A.

BSS110

Fixture mounting/wiring channel is formed and welded 20 ga. steel chemically treated to resist corrosion and enhance paint adhesion

LED housing is extruded aluminum with sheet aluminum end caps

Standard fixture finish is semi-gloss white powder coat, applied post production

Asymmetric and general diffuse extruded acrylic lens options available

Available in nominal lengths of 2’, 3’, 4’ and 5’

LED housing rotates and locks in place without tools at -15°, 0°, 15°, 30°, 45°, 60°, 75°, 90° and 105°

Knock outs on ends, and underside accept standard electrical fittings by others

Standard integral 120V-277V driver offered with 0-10V dimming or non-dim (other dimming driver options available)

Integral 120-277V emergency battery backup available for 4’ nominal non-dim or 0-10V (consult factory for all other lengths/drivers)

Standard outputs range from 465 to 655 lumens per foot, dependent on optic option

LEDs available in 2700K, 3000K, 3500K, and 4000K, within a 3 step MacAdam ellipse, all with 90+ CRI typical

Life: 50,000 hours L70

Limited five year warranty

UL and C-UL listed for dry and damp locations

IBEW manufactured and assembled

Made in U.S.A.

BSS521

Fixture constructed of an extruded aluminum housing, frosted acrylic extruded lens and sheet aluminum end caps

Fixture arms are constructed of steel pipe, Ø3/4” extruded aluminum sleeves and machined aluminum end cap couplers

Includes Ø4-3/4” x 1/8” thick aluminum plates and screws for mounting to 4” octagonal wall boxes (by others)

Standard finishes include architectural white (semi-matte), white (semi-gloss), black (semi-matte), matte black, environmental satin silver (alternative to anodize), bronze and primer powder coat, applied post production (consult factory for custom finishes)

Satin anodize finish also available (may require additional lead time)

Available in nominal lengths of 24”–68” single fixtures and continuous runs

Arms allow fixture to project from a wall or ceiling nominally 4”, 6”, 12” or 18”

Fixture housing rotates 338° and is locked in place with hex fastener

Standard integral 120-277V driver offered with 0-10V dimming or non-dim (other dimming driver options available)

Remote mounted emergency battery backup available (ordered separately, consult factory for details)

Standard outputs are 5W and 8W nominal per foot

LEDs available in 3000K, 3500K, 4000K, 5000K, all with a typical 84-85 CRI and color consistency within a 3 step MacAdam ellipse

Life: 50,000 hours L70

Limited five year warranty

UL and C-UL listed for dry and damp locations

IBEW manufactured and assembled

Made in U.S.A.

BSS260

Fixture constructed of extruded aluminum housing, frosted extruded acrylic lenses and machined aluminum end caps.

Model variations offered for wall mount and cable suspended applications.

Standard finishes include architectural white (semi-matte), white (semi-gloss), black (semi-matte), matte black, environmental satin silver (alternative to anodize), bronze and primer powder coat, applied post production (consult factory for custom finishes).

Satin anodize finish also available (may require additional lead time).

Available in nominal lengths of 2’–8′ single fixtures and continuous runs.

Basic continuous run fixtures provided with 18 ga. wiring harness for 6 Amp maximum load (consult factory for runs requiring sensor integration, etc.).

Standard integral 120-277V driver offered with 0-10V dimming or non-dim (other dimming driver options available).

Remote mounted emergency battery backup available (ordered separately, consult factory for details).

Standard outputs are 5W and 8W nominal per foot, per lighting element.

LEDs available in 3000K, 3500K, 4000K, 5000K, all with a typical 84-85 CRI and color consistency within a 3 step MacAdam ellipse.

Life: 50,000 hours L70.

Bartco Lighting Controls Capable fixture available with integrated controls from a variety of suppliers.

Limited five year warranty.

UL and C-UL listed for dry and damp locations.

IBEW manufactured and assembled.

Made in U.S.A.

BFL117

  • Fully assembled housing is formed and welded, 20 ga. steel, chemically treated to resist corrosion and enhance paint adhesion
  • Available in white, black, silver, platinum or bronze powdercoat finish
  • Clean body
  • Rotational locking lamp holders
  • Available for one T5 14W, 21W, 28W, 35W or high output 24W, 39W, 54W, 80W linear fluorescent lamps
  • Standard 120V – 277V electronic high power factor ballast is pre-wired to the lamp holders (consult factory for other voltage options)
  • Dimming and emergency battery back up options available (consult factory for availability and stystem compatibility)
  • UL and C-UL listed for dry and damp locations
  • IBEW manufactured and labeled
  • Made in the U.S.A.

IPR5S-OCC

  • Fully assembled housing is formed and welded, 20 ga. steel, chemically treated to resist corrosion and enhance paint adhesion
  • Model variations offered for surface, cable suspended and pendant mount applications
  • Available in standard white, black, silver, platinum, bronze and primer powder coat, applied post production (consult factory for custom finishes)
  • Includes frosted or linear prismatic acrylic lens
  • Available for T5 14W, 21W, 28W, 35W linear fluorescent lamps in single and some tandem lengths
  • Standard ballast is specification grade 120V-277V program start (consult factory for other voltage options)
  • Dimming, emergency battery backup and specialized ballast factor options available (consult factory for availability and system compatibility
  • Knock-outs on back accept standard electrical fittings by others (consult factory for other locations)
  • Rotational locking lamp holders
  • UL and C-UL listed for dry and damp locations
  • IBEW manufactured and labeled
  • Made in the U.S.A

 

CB5

Fully assembled housing is formed and welded, 20 ga. steel, chemically treated to resist corrosion and enhance paint adhesion

Model variations offered for surface, cable suspended and pendant mount applications

An accessory symmetrical reflector in matching finish is available

Available for T5 14W, 21W, 28W, 35W and high output 24W, 39W, 54W, 80W lamps in single length, some tandem lengths and continuous runs

Standard ballast is specification grade 120V-277V program start (consult factory for other voltage options)

Dimming, emergency battery backup and specialized ballast factor options available (refer to supplemental ballast details sheet for availability)

Knock outs on back of surface mount model accept standard electrical fittings by others (consult factory for other locations)

UL and C-UL listed for dry and damp locations

IBEW manufactured and assembled

Made in U.S.A.

IEL5S

  • Fully assembled housing is formed and welded, 20 ga. steel, chemically treated to resist corrosion and enhance paint adhesion
  • Model variations offered for surface, cable suspended and pendant mount applications
  • Available in standard white, black, silver, platinum, bronze and primer powder coat, applied post production (consult factory for custom finishes)
  • Available for one T5 14W, 21W , 28W, 35W and high output 24W, 39W, 54W and 80W linear fluorescent lamps
  • Standard ballast is specification grade 120V-277V program start (consult factory for other voltage options)
  • Dimming, emergency battery backup and specialized ballast factor options available (consult factory for availability and system compatibility
  • Knock-outs on back accept standard electrical fittings by others (consult factory for other locations)
  • Rotational locking lamp holders
  • UL and C-UL listed for dry and damp locations
  • IBEW manufactured and labeled
  • Made in the U.S.A.

IPR8MS-OCC

  • Fully assembled housing is formed and welded, 20 ga. steel, chemically treated to resist corrosion and enhance paint adhesion
  • Model variations offered for surface, cable suspended and pendant mount applications
  • Available in standard white, black, silver, platinum, bronze and primer powder coat, applied post production (consult factory for custom finishes)
  • Includes frosted or linear prismatic acrylic lens
  • Available for one or two T8 17W, 25W, 32W, and 40W linear fluorescent lamps in single and some tandem lengths
  • Standard ballast is specification grade 120V-
  • 277V program start (consult factory for other voltage options)
  • Dimming, emergency battery backup and specialized ballast factor options available (consult factory for availability and system compatibility
  • Knock-outs on back accept standard electrical fittings by others (consult factory for other locations)
  • Rotational locking lamp holders
  • UL and C-UL listed for dry and damp locations
  • IBEW manufactured and labeled
  • Made in the U.S.A.

 

BFL270

  • Fully assembled housing is formed, 20 ga. steel, chemically treated to resist corrosion and enhance paint adhesion
  • Standard finish is high reflectance white powder coat, applied post production
  • Rotational locking lamp holders
  • Installed end feed connector accepts 3/8″ steel flex conduit (available separately)
  • Wired with 12′ leads
  • Easy mounting through provided holes in housing
  • Available for T5 8W, 13W, 14W, 21W, 28W, 35W and high output 24W, 39W, 54W, 80W linear fluorescent lamp in single and tandem lamp models
  • UL and ULC listed for dry and damp locations
  • Approved for use as a light in the storage area of a closet as defined by the 2008 NEC Article 410
  • Tube guard or lens recommended for use in closet applications
  • Requires a remote ballast and enclosure (ordered separately)
  • IBEW manufactured and labeled
  • Made in the U.S.A.

NOTE: Lamp holders are wired for rapid start ballasts with the exception of 8W and 13W models which are wired for instant start ballasts.

 

BCR100

Fixture constructed of an extruded aluminum housing, extruded, frosted acrylic lens and sheet aluminum end caps.

Fixture mounts to closet walls with machined aluminum cup-style holders.

Standard finishes include architectural white (semi-matte), white (semi-gloss), black (semi-matte), matte black, environmental satin silver (alternative to anodize), bronze and primer powder coat, applied post production (consult factory for custom finishes).

Satin anodize finish also available (may require additional lead time).

Available for closet openings of 12”–96” nominal.

Fixed length or adjustable intermediate supports required for 36” and longer fixtures with 33 lbs. capacity for every 36” of length between supports.

Fixtures wired with 10’ low voltage leads.

Included standard remote 120-277V driver offered with 0-10V dimming or non-dim (other dimming driver options available).

Standard output is 520 lumens per foot.

LEDs available in 2700K, 3000K, 3500K, and 4000K, within a 3 step MacAdam ellipse, all with 90+ CRI typical.

Life: 50,000 hours L70.

Limited five year warranty.

UL and C-UL listed for storage spaces.

IBEW manufactured and assembled

Made in U.S.A.